Welcome to the official website of Changzhou Electric Co., Assunta!
中文|Enligh
National Service Hotline

ST-213H drive two-phase stepper

Your location:首页 > Products > Stepper Drives > ST-213H drive two-phase stepper

ST-213H the two-phase drive

Date:2015-07-18    Read:[ ] 次

 213H.jpg

一. ST-213H features of the two-phase drive

1, low speed when using the second subdivision control technology, low speed resonance greatly reduced.

2, the internal over-current, over voltage, over temperature protection circuits.

3, each phase maximum drive current of 7.0 amps peak, and the current sixteen-speed adjustable.

5, using no over-current, twenty thousand times per second bipolar constant-current chopping technique.

6, sixteen the number of optional gear segments, the maximum resolution 51200 steps / rev.

7, a single pulse or double pulse operation mode is optional.

8, the maximum 200KHz frequency response. Phase power automatic memory function

二. Instructions for use:

1, Port Description:                                    

ST-213H drive pin port Description

CP+/CW+

Pulse / CW pulse signal positive

CP-/CW-

Pulse / CW puls signal negative terminal

DIR+/CCW+

Directional level / reverse pulse signal positive

DIR-/CCW-

Directional level / reverse pulse signal negative terminal

FREE+/FREE-

Enable level signal positive / negative terminal

ALM+/ALM-

Alarm output is negative

A+A-B+B-

Motor input port

L-N

AC 220V

K1~K4

DIP subdivision combination

K5

ON pulse input, OFF direction signal input

K6

Full flow setting ON, OFF half flow setting

K7-K10

Current combination DIP

 

 

 

 

 

 

 

 

 

 

 

   

 

 

   

 

   Note: 1, when the input signal is greater than 5V, 12V general increase 1.2K, 24V plus 2K resistance


       2, dial code required in the absence of power is set to take effect. Change the power on again subdivided

  2, thumbwheels set: breakdown and current setting (K1-K10)                        

K1

K2

K3

K4

Subdivision

K7

K8

K9

K10

Electric current

ON

ON

ON

ON

1

OFF

OFF

OFF

OFF

1.5

ON

ON

ON

OFF

2

OFF

OFF

OFF

ON

1.8

ON

ON

OFF

ON

4

OFF

OFF

ON

OFF

2.2

ON

ON

OFF

OFF

5

OFF

OFF

ON

ON

2.5

ON

OFF

ON

ON

6

OFF

ON

OFF

OFF

2.8

ON

OFF

ON

OFF

8

OFF

ON

OFF

ON

3.2

ON

OFF

OFF

ON

10

OFF

ON

ON

OFF

3.4

ON

OFF

OFF

OFF

12

OFF

ON

ON

ON

3.8

OFF

ON

ON

ON

16

ON

OFF

OFF

OFF

4.2

OFF

ON

ON

OFF

20

ON

OFF

OFF

ON

4.6

OFF

ON

OFF

ON

32

ON

OFF

ON

OFF

5.0

OFF

ON

OFF

OFF

40

ON

OFF

ON

ON

5.4

OFF

OFF

ON

ON

50

ON

ON

OFF

OFF

5.8

OFF

OFF

ON

OFF

64

ON

ON

OFF

ON

6.2

OFF

OFF

OFF

ON

128

ON

ON

ON

OFF

6.6

OFF

OFF

OFF

OFF

256

ON

ON

ON

ON

7.0

K5

ON

Single pulse

K6

ON

      Full flow

OFF

Double pulse

OFF

Semiflows

                       

 

     

 

 

  

 

 

 

 

 

 

 

 

 

 

   

 

   

 

 

     

 

     4Drive Overall installation diagram

2.jpg